START_INST_TAB  = p_idsdb
VERSION         = V01.08
DATE            = 96/12/16
AUTHOR          = Ramon, I. Heinrichsen, L. Orsini, U. Klaas
COMMENT
COMMENT ***************************************************************
COMMENT
COMMENT           Instrument Default Settings Data Base
COMMENT
COMMENT                         (IDSDB)
COMMENT
COMMENT 
COMMENT
COMMENT Update of SER_FCS1_POWER to 0.726 mW for rev 78 - AW/GP (02/02/96)
COMMENT
COMMENT New default settings for optional dark and cold FCS measurements
COMMENT with all PHT-P and PHT-C detectors in revised AOTs P05 and P25 added
COMMENT
COMMENT New parameters to split the wait w.r.t. heating of the P2 detetor
COMMENT before and after ther latch-up prevention - IH (5.8.96)
COMMENT
COMMENT Parameters w.r.t. heating time P2 updated to avoid latch-up
COMMENT	IH(29.8.96)
COMMENT
COMMENT Change of parameters C1W2DARK and C2W2DARK for consistent use with ICS
COMMENT PS0003 (C1W2DARK = C200_200_UM ---> C1W2DARK = 10_SEC,
COMMENT         C2W2DARK = C100_50_UM  ---> C2W2DARK = 99_SEC)  UK (28/09/96)
COMMENT
COMMENT
COMMENT	Change of parameters P1CF_EXP, P2CF_EXP, P3CF_EXP and C1CF_EP from
COMMENT 7 to 8, i.e. the exposure time for the dark FCS measurement increased 
COMMENT	from 128s to 256s. (IH. 16.12.96, SPR 2167)
COMMENT
COMMENT
COMMENT Preamplifier gain and off-set settings for the PHT detectors:
COMMENT
COMMENT P1_PAF_OFFSET, P1_PAF_GAIN
COMMENT P2_PAF_OFFSET, P2_PAF_GAIN 
COMMENT P3_PAF_OFFSET, P3_PAF_GAIN
COMMENT C100_PAF_OFFSET, C100_PAF_GAIN  
COMMENT C200_PAF_OFFSET, C200_PAF_GAIN
COMMENT S1_PAF_OFFSET, S1_PAF_GAIN
COMMENT S2_PAF_OFFSET, S2_PAF_GAIN
COMMENT
COMMENT Stabilization times after heat control on of heated 
COMMENT detectors P1, P2, P3, C100, C200, S
COMMENT Times are give in [s]
COMMENT	The times for the P2 detector _1 and _2 are the wait times before
COMMENT and after the P2 latch-up prevention respcetively
COMMENT
COMMENT P1_STAB_TIME    
COMMENT P2_STAB_TIME_1
COMMENT P2_STAB_TIME_2    
COMMENT P3_STAB_TIME   
COMMENT C100_STAB_TIME 
COMMENT C200_STAB_TIME 
COMMENT S_STAB_TIME 
COMMENT 
COMMENT Bias coarse (RANGE) and fine settings for the PHT detectors
COMMENT For the C200 array the four pixels are individually supplied 
COMMENT with bias (C2001...C2004).
COMMENT
COMMENT P1_BIAS_RANGE, P1_BIAS        
COMMENT P2_BIAS_RANGE, P2_BIAS        
COMMENT P3_BIAS_RANGE, P3_BIAS        
COMMENT C100_BIAS_RANGE, C100_BIAS      
COMMENT C200_BIAS_RANGE, C2001_BIAS, C2002_BIAS, C2003_BIAS, C2004_BIAS
COMMENT S1_BIAS, S2_BIAS
COMMENT
COMMENT Stabilization time after changing bias from standby to on in [s]
COMMENT
COMMENT P1_BIAS_STAB   
COMMENT P2_BIAS_STAB   
COMMENT P3_BIAS_STAB   
COMMENT C100_BIAS_STAB 
COMMENT C200_BIAS_STAB
COMMENT S_BIAS_STAB 
COMMENT 
COMMENT The filter mnemonic for the filter used during the PHT 
COMMENT serendipity mode observations is specified in 
COMMENT
COMMENT SER_FILTER
COMMENT
COMMENT The same settings as given above for the C200 array when 
COMMENT operated in serendipity mode. In addition the time for the 
COMMENT FCS calibration of the serendipity mode is specified as a 
COMMENT power of two in SER_FCS_EXP and the power and mode of the FCS
COMMENT 
COMMENT SER_PAF_OFFSET 
COMMENT SER_PAF_GAIN   
COMMENT SER_BIAS_RANGE 
COMMENT SER_C2001_BIAS 
COMMENT SER_C2002_BIAS 
COMMENT SER_C2003_BIAS 
COMMENT SER_C2004_BIAS 
COMMENT SER_TRS1_MODE  
COMMENT SER_FCS1_POWER 
COMMENT SER_FCS_EXP    
COMMENT
COMMENT For the PHT serendipity mode also the cold read out electronics 
COMMENT check-out voltage is contained in the ISDB and is not derived 
COMMENT via the table CRE as the reset interval RI is fixed in this case.
COMMENT
COMMENT SER_CRE_RANGE, SER_CRE_ADD    
COMMENT
COMMENT The electronic settings for the PHT-S dark measurements are given 
COMMENT in the following settings. Each PHT-S AOT is accompanied by a dark 
COMMENT current measurement.
COMMENT
COMMENT S_DARK_DATA_RED 
COMMENT S_DARK_FREQ
COMMENT S_DARK_LOG2_RI  
COMMENT S_DARK_LOG2_DR  
COMMENT S_DARK_LOG2_NDR 
COMMENT S_DARK_EXP
COMMENT
COMMENT As a consequence of the new raster logics three new entries in 
COMMENT the IDSDB are needed
COMMENT	The times for the P2 detector _1 and _2 are the wait times before
COMMENT and after the P2 latch-up prevention respcetively
COMMENT
COMMENT BREAK_HEAT_P2_1
COMMENT BREAK_HEAT_P2_2
COMMENT BREAK_HEAT_P3
COMMENT BREAK_HEAT_C100
COMMENT
COMMENT As a consequence of the re-design of AOTs P05 and P25 including
COMMENT optional dark and cold FCS measurements 73 new parameters defining
COMMENT the set-up for these measurements are included
COMMENT
COMMENT dark positions of all three change wheels for detectors P1, P2, P3,
COMMENT C100, and C200
COMMENT P1W1DARK, P1W2DARK, P1W3DARK   for P1 (PHT_S, 5_SEC, P3_100_UM)
COMMENT P2W1DARK, P2W2DARK, P2W3DARK   for P2 (PHT_S, 5_SEC, P1_3P29_UM)
COMMENT P3W1DARK, P3W2DARK, P3W3DARK   for P3 (PHT_C_NO_POL, 5_SEC, P1_11P5_UM)
COMMENT C1W1DARK, C1W2DARK, C1W3DARK for C100 (PHT_S, 10_SEC, P3_100_UM)
COMMENT C2W1DARK, C2W2DARK, C2W3DARK for C200 (PHT_S, 99_SEC, P3_100_UM)
COMMENT
COMMENT read-out electronics and CRE check-out voltage settings for
COMMENT dark measurements
COMMENT P1DKDATA        P1 data reduction factor
COMMENT P1DK_RI_MNE     P1 reset interval mnemonic
COMMENT P1DK_DR         P1 destructive read-out setting
COMMENT P1DK_NDR        P1 non-destructive read-out setting
COMMENT P1DK_EXP        P1 dark exposure time
COMMENT P2DKDATA        P2 data reduction factor
COMMENT P2DK_RI_MNE     P2 reset interval mnemonic
COMMENT P2DK_DR         P2 destructive read-out setting
COMMENT P2DK_NDR        P2 non-destructive read-out setting
COMMENT P2DK_EXP        P2 dark exposure time
COMMENT P3DKDATA        P3 data reduction factor
COMMENT P3DK_RI_MNE     P3 reset interval mnemonic
COMMENT P3DK_DR         P3 destructive read-out setting
COMMENT P3DK_NDR        P3 non-destructive read-out setting
COMMENT P3DK_EXP        P3 dark exposure time
COMMENT C1_CRE_RNGDK    C100 CRE check-out voltage range
COMMENT C1_CRE_OFFSDK   C100 CRE check-out voltage offset
COMMENT C1DKDATA        C100 data reduction factor
COMMENT C1DK_RI_MNE     C100 reset interval mnemonic
COMMENT C1DK_DR         C100 destructive read-out setting
COMMENT C1DK_NDR        C100 non-destructive read-out setting
COMMENT C1DK_EXP        C100 dark exposure time
COMMENT C2_CRE_RNGDK    C200 CRE check-out voltage range
COMMENT C2_CRE_OFFSDK   C200 CRE check-out voltage offset
COMMENT C2DKDATA        C200 data reduction factor
COMMENT C2DK_RI_MNE     C200 reset interval mnemonic
COMMENT C2DK_DR         C200 destructive read-out setting
COMMENT C2DK_NDR        C200 non-destructive read-out setting
COMMENT C2DK_EXP        C200 dark exposure time
COMMENT
COMMENT read-out electronics and CRE check-out voltage settings for
COMMENT cold FCS measurements
COMMENT P1CFDATA        P1 data reduction factor
COMMENT P1CF_RI_MNE     P1 reset interval mnemonic
COMMENT P1CF_DR         P1 destructive read-out setting
COMMENT P1CF_NDR        P1 non-destructive read-out setting
COMMENT P1CF_EXP        P1 cold FCS exposure time
COMMENT P2CFDATA        P2 data reduction factor
COMMENT P2CF_RI_MNE     P2 reset interval mnemonic
COMMENT P2CF_DR         P2 destructive read-out setting
COMMENT P2CF_NDR        P2 non-destructive read-out setting
COMMENT P2CF_EXP        P2 cold FCS exposure time
COMMENT P3CFDATA        P3 data reduction factor
COMMENT P3CF_RI_MNE     P3 reset interval mnemonic
COMMENT P3CF_DR         P3 destructive read-out setting
COMMENT P3CF_NDR        P3 non-destructive read-out setting
COMMENT P3CF_EXP        P3 cold FCS exposure time
COMMENT C1_CRE_RNGCF    C100 CRE check-out voltage range
COMMENT C1_CRE_OFFSCF   C100 CRE check-out voltage offset
COMMENT C1CFDATA        C100 data reduction factor
COMMENT C1CF_RI_MNE     C100 reset interval mnemonic
COMMENT C1CF_DR         C100 destructive read-out setting
COMMENT C1CF_NDR        C100 non-destructive read-out setting
COMMENT C1CF_EXP        C100 cold FCS exposure time
COMMENT C2_CRE_RNGCF    C200 CRE check-out voltage range
COMMENT C2_CRE_OFFSCF   C200 CRE check-out voltage offset
COMMENT C2CFDATA        C200 data reduction factor
COMMENT C2CF_RI_MNE     C200 reset interval mnemonic
COMMENT C2CF_DR         C200 destructive read-out setting
COMMENT C2CF_NDR        C200 non-destructive read-out setting
COMMENT C2CF_EXP        C200 cold FCS exposure time
COMMENT
COMMENT ***************************************************************
COMMENT 
NUM_ENTRIES     = 138
P1_PAF_OFFSET   = 0.0000
P1_PAF_GAIN     = 8
P2_PAF_OFFSET   = 0.0000
P2_PAF_GAIN     = 8
P3_PAF_OFFSET   = 0.0000
P3_PAF_GAIN     = 8
C100_PAF_OFFSET = 0.0000
C100_PAF_GAIN   = 8
C200_PAF_OFFSET = 0.0000
C200_PAF_GAIN   = 8
S1_PAF_OFFSET   = 0.0000
S1_PAF_GAIN     = 8
S2_PAF_OFFSET   = 0.0000
S2_PAF_GAIN     = 8
P1_STAB_TIME    = 0
P2_STAB_TIME_1  = 70
P2_STAB_TIME_2  = 16
P3_STAB_TIME    = 90
C100_STAB_TIME  = 90
C200_STAB_TIME  = 0
S_STAB_TIME     = 0
P1_BIAS_RANGE   = M3P0_VOLT
P1_BIAS         = -90.00
P2_BIAS_RANGE   = M10P0_VOLT
P2_BIAS         = 0.00
P3_BIAS_RANGE   = M0P6_VOLT
P3_BIAS         = 0.3500
C100_BIAS_RANGE = M0P6_VOLT
C100_BIAS       = 0.4200
C200_BIAS_RANGE = M0P25_VOLT
C2001_BIAS      = 0.1700
C2002_BIAS      = 0.1700
C2003_BIAS      = 0.1700
C2004_BIAS      = 0.1700
S1_BIAS         = -37.00
S2_BIAS         = -37.00
P1_BIAS_STAB    = 0
P2_BIAS_STAB    = 0
P3_BIAS_STAB    = 0
C100_BIAS_STAB  = 6
C200_BIAS_STAB  = 0
S_BIAS_STAB     = 0
SER_FILTER      = C200_160_UM
SER_PAF_OFFSET  = 0.0000
SER_PAF_GAIN    = 8
SER_BIAS_RANGE  = M0P25_VOLT
SER_C2001_BIAS  = 0.1700
SER_C2002_BIAS  = 0.1700
SER_C2003_BIAS  = 0.1700
SER_C2004_BIAS  = 0.1700
SER_TRS1_MODE   = TRS2_ON
SER_FCS1_POWER  = 0.726
SER_FCS_EXP     = 4
SER_CRE_RANGE   = 0_VOLT
SER_CRE_ADD     = 0.0
S_DARK_DATA_RED = 1
S_DARK_FREQ     = 8192
S_DARK_LOG2_RI  = 2
S_DARK_LOG2_DR  = 5
S_DARK_LOG2_NDR = 5
S_DARK_EXP      = 5
BREAK_HEAT_P2_1 = 50
BREAK_HEAT_P2_2 = 6
BREAK_HEAT_P3   = 60
BREAK_HEAT_C100 = 60
P1W1DARK        = PHT_S
P1W2DARK        = 5_SEC
P1W3DARK        = P3_100_UM
P2W1DARK        = PHT_S
P2W2DARK        = 5_SEC
P2W3DARK        = P1_3P29_UM
P3W1DARK        = PHT_C_NO_POL
P3W2DARK        = 5_SEC
P3W3DARK        = P1_11P5_UM
C1W1DARK        = PHT_S
C1W2DARK        = 10_SEC
C1W3DARK        = P3_100_UM
C2W1DARK        = PHT_S
C2W2DARK        = 99_SEC
C2W3DARK        = P3_100_UM
P1DKDATA        = 1
P1DK_RI_MNE     = 3
P1DK_DR         = 4
P1DK_NDR        = 7
P1DK_EXP        = 8
P2DKDATA        = 1
P2DK_RI_MNE     = 3
P2DK_DR         = 4
P2DK_NDR        = 7
P2DK_EXP        = 8
P3DKDATA        = 1
P3DK_RI_MNE     = 3
P3DK_DR         = 4
P3DK_NDR        = 7
P3DK_EXP        = 8
C1_CRE_RNGDK    = M0P25_VOLT
C1_CRE_OFFSDK   = 0.237
C1DKDATA        = 1
C1DK_RI_MNE     = 3
C1DK_DR         = 4
C1DK_NDR        = 7
C1DK_EXP        = 8
C2_CRE_RNGDK    = M0P25_VOLT
C2_CRE_OFFSDK   = 0.237
C2DKDATA        = 1
C2DK_RI_MNE     = 3
C2DK_DR         = 4
C2DK_NDR        = 7
C2DK_EXP        = 8
P1CFDATA        = 1
P1CF_RI_MNE     = 3
P1CF_DR         = 4
P1CF_NDR        = 7
P1CF_EXP        = 8
P2CFDATA        = 1
P2CF_RI_MNE     = 3
P2CF_DR         = 4
P2CF_NDR        = 7
P2CF_EXP        = 8
P3CFDATA        = 1
P3CF_RI_MNE     = 3
P3CF_DR         = 4
P3CF_NDR        = 7
P3CF_EXP        = 8
C1_CRE_RNGCF    = M0P25_VOLT
C1_CRE_OFFSCF   = 0.237
C1CFDATA        = 1
C1CF_RI_MNE     = 3
C1CF_DR         = 4
C1CF_NDR        = 7
C1CF_EXP        = 8
C2_CRE_RNGCF    = M0P25_VOLT
C2_CRE_OFFSCF   = 0.237
C2CFDATA        = 1
C2CF_RI_MNE     = 3
C2CF_DR         = 4
C2CF_NDR        = 7
C2CF_EXP        = 7
END_INST_TAB


############################################################################
#
# Effective Revision History for P_IDSDB
# Author: Luciano Orsini
# Creation Date: 09/03/94
#
# Version: $Id: p_idsdb.txt,v 1.8 1997/01/08 07:16:29 soclib Exp $
#

#
# Revision History: $Log: p_idsdb.txt,v $
# Revision 1.8  1997/01/08  07:16:29  soclib
# SOCLIB:
# DRB_96_183
# Changes: pidsdb.txt - SPR 2167
# p_aottim.txt p_cfiltr.txt and p_pfiltr.txt - SPR 2168
#
# Revision 1.7  1996/09/30  11:28:58  soclib
# SOCLIB:
# SPR 2069
# DRB_96_163
#
# Revision 1.6  1996/08/29  12:02:24  soclib
# SOCLIB:
# SCREW 252
# DRB_96_152
#
# Revision 1.5  1996/02/02  08:24:23  soclib
# SOCLIB:
# DRB_96_042
# Update for rev 78
#
# Revision 1.4  1995/05/05  09:36:17  lorsini
# Reference: SPR-0563
# Software Change:
# 	Changed SER_FCS_EXP = 15 to SER_FCS_EXP = 4 .
#
# Revision 1.3  1994/11/15  08:35:27  ittlib
# Update to logic to version 2.3
#
# Revision 3.9  1994/10/10  13:41:15  lorsini
# Changed value for S_DARK_FREQ to 8192.
#
# Revision 3.8  1994/09/22  08:27:55  lorsini
# The old statements
#    START_IDSDB     = INS and
#    START_SETTINGS  = INS
# are now
#    START_INST_TAB = I_idsdb and
#    START_INST_TAB = I_setngs
# and the end table keywords
#    END_IDSDB and END_SETTINGS
# are now
#    END_INST_TAB
#
# Revision 3.7  1994/09/22  07:51:27  lorsini
# Changed table name to be p_idsdb according ISO/SSD/ICD-01, Issue 3.0 01/09/94
#
# Revision 3.6  1994/07/19  13:06:22  lorsini
# IH: Update FM parameters for EE1 test, 14.7.94
#
# Revision 3.5  1994/07/19  12:44:32  aotlib
# Remove blank causing error in aot_pack at line : 152.
#
# Revision 3.4  1994/07/14  13:20:54  lorsini
# Modfied P1 P2 BIAS Mnemonic and removed TBD values.
#
# Revision 3.3  1994/04/22  14:07:53  lorsini
# Corrected start table keyworg from PHT_* to PHT only.
#
# Revision 3.2  1994/04/22  13:55:48  lorsini
# Change Table name from P_* to PHT_*
#
# Revision 3.1  1994/03/15  09:35:55  lorsini
# Development for EE1 test ( Initial Version ).
#
#
